Camplux Propane Off-Grid Portable Water Heater for RV, Trailer & Camper - White

Description

• CSA approved portable tankless water heater for US &Canada markets. Lowest water pressure start up just need 3.0 PSI! Also works great with Camplux 12V 1.2 GPM water pump. You don't need buy extra accessories,you can get 2 pcs extension hose and fittings,complete pump package all in one.
• Wide comfortable water temperature range from 8℃-46℃ (46.4℉-114.8℉), 1.32 gallons per minute of hot water output, you can get instant on-demand hot water easily .
• Compact and lightweight size tankless water heaterwith folding handle keeps it out of the way, allowing for a convenient set-up outdoors,great for off-grid,road trips,camping trips.
• Flame failure device, anti-freezing protection,over heating protection,oxygen depletion safety shut-off protection always ensures you wonderful and safety outdoor showers.To avoid gas leakage caused by improper sealing of the water heater, DO NOT TWINE TEFLON TAPE between gas regulator and gas inlet pipe. The tankless water heater will "caught on fire "with improper operation. Always check gas leakage before operation.

Product Specifications

Camplux Propane Off-Grid Portable Water Heater for RV, Trailer & Camper - White Product Specifications

What's in the Box?

1 X 5L Tankless Water Heater
1 X 12V Water Pump
1 X 5 Feet CSA Gas Regulator
1 X 5 Feet Shower Head
2 X 6.5 Feet Extension Hoses w/ Quick Connector
1 X Installation Hardware Pack
2 X US Standard Garden Hoses
1 X Users Manual

Product Manual

Camplux Propane Off-Grid Portable Water Heater for RV, Trailer & Camper - White Product Manual

Camplux Water Heater for RV Product Manual

Winterize Tip

Safe Storage Steps

1. Turn off the water heater, take out the batteries
2. Disconnect all inlet and outlet connections from the water heater(there maybe leak out, please prepare with a bucket or rags)
3. Unplug the drain plug in the bottom of the unit, tilt on it’s sides to drain it off completely
4. Store indoors in a dry environment until next use

Product FAQs

Camplux Water Heater Product FAQs

1. My water heater is not igniting

A. Check if the polarity of the batteries are positioned correctly.
B. Check if the water inlet, water outlet and gas inlet are connected to the right pipes.
C. Heater wont ignite if the water pressure is too low, please make sure you have enough water flow.
D. Check the water inlet and filter to make sure there is no clog.
E. Disconnect the shower hose and shower head and let the water gush out from the heater (set gas knob to minimum and water knob to maximum), if it ignites that means there is a clog either in shower hose or shower head.

2. Water Heater Ignites but not producing hot water

A. If it’s the first time you start the heater, to exhaust the extra air completely, please try start it couple of times.
B. Disconnect the gas hose from the gas inlet and check if the gas is flowing. If the regulator is defective the gas will not flow and the unit will not ignite.
C. Check if you have enough propane.
D. If you are using a new tank of gas, the solenoid valve may not work because the gas pressure is too high. Try to turn on the water faucet first, gas source valve later. And try to start the heater again.
E. Disconnect the shower hose and shower head and let the water gush out from the heater (set gas knob to minimum and water knob to maximum), if that fix the problem there is clog either in shower hose or shower head. 

PRECAUTION:
F. Please make sure the water heater is connected to the correct type of gas line. If the unit is LP it should be connected to LP line or NG to NG line. It’s possible to cause an ignition failure or an explosion when connected to the wrong gas line. It’ll produce yellow flame or black smoke if connected to the wrong gas line.

3. Heater ignites with a loud noise

A. Kindly restart the water heater few times to exhaust the extra air inside. If does not fix the problem try to replace the gas regulator using a standard grill regulator.
B. Check if the screws are properly secured if the water heater is mounted.
C. Check the battery if it’s still okay.

4. Water Heater flames out suddenly

A. Check if you still have enough gas. Check your gas cylinder.
B. Check if the water pressure is too low to ignite the heater. If you are using well water it is best to use a water pump to increase the pressure.
C. Change the batteries.
D. Disconnect the shower hose and shower head and let the water gush out from the heater (set gas knob to minimum and water knob to maximum), if that fix the problem there is clog either in shower hose or shower head.

5. What to check if the water doesn't heat up?

A. Turn up the gas knob and turn down the water knob.
B. Turn on the gas valve completely.
C. Shorten the gas pipe if it is longer than 5 meters.
D. Choose a suitable gas regulator for low pressure.
E. Avoid using gas in multiple appliances all at the same time.

6. Black smoke coming out from Water heater

A. Open the front panel of the water heater and air blow the heat exchanger with an air compressor to remove if there is any debris or clog inside. After, set the gas knob to minimum and water knob to maximum and start the water heater and check if the black smoke will be gone.
B. If the issue still persist unplug the gas line and stop using the water heater. Call for service.

7. Heater may suddenly start producing too much hot water

A.check and reduce your heater’s temperature setting.

B.you must fully open the shut-off valve and ensure more water flow

8. Heater Yellow Flame

While your Camplux water heater is functioning normally, it will produce a deep blue flame. But when your heater produces a yellow flame, you can’t overlook it as it is another problem. 

Yellow flame causes extreme smoking and dirt build-up in the flue tubes, combustion chamber, and gas burner.

A.On your Camplux water heater’s front cover, you will see the middle horizontal window or viewer panels. Look through the window to check whether your heater produces a blue or yellow flame,We strongly recommend you not to use your Camplux water heater when it produces a yellow flame.

B.Replace the cracked gas regulator.

C.From the gas burner’s top, remove the scale and adequately clean the burner and unclog the main burner.

D.Ensure sufficient air circulation and proper ventilation in your heater.

E.Clean the pipes properly and remove the vent or flue’s blockage.

9. Water Heater Leaking

A.Check the correct installation.

B.Check and tighten your water tank’s pipe connection.

C.Replace the cracked heater, malfunctioning T & P relief valve, loose or damaged gaskets, lousy drain valve, and the defective hot and cold water inlet and outlet.

10. Water Heater Error Codes

E0：Hot water sensor not working.

Causes : Short circuit. Loose junction pat. A defective or broken sensor. 

Solutions : Prevent your heater’s overheating to avoid short circuits. Tighten the junction pat. Replace the broken or faulty sensor.

E1：Failed ignition system.

Causes : Loose junction pat. Close or partially open gas valve. Close water shut-off valve. 

Solutions : Tighten the junction pat. Check and open the gas and water shutoff valve fully. 

E2：Flame Failure Protection.

Causes : The heater fails to detect the flame. The gas supply is off. Empty tank or low fuel supply. Damaged fuel sensor.

Solutions : Ensure your water heater is perfectly detecting the flame. Check and turn on the gas supply. Refill the fuel tank and ensure proper fuel supply. Replace the faulty fuel sensor.

E3：Overheating protection.

Causes : Overheating controller. Dry combustion.

Solutions : Ensure your heater controller is not overheating.

E5：Pressure switch failure.

Causes : Too low power supply voltage. Motor malfunction.

Solutions : Ensure high power supply voltage. Replace the bad motor. 

E7：Solenoid Valve.

Causes : Valve’s open circuit. Valve’s short circuit. Faulty or disconnected valve. 

Solutions : Prevent the valve’s opening and short circuit. Replace the lousy valve. Make sure the valve is properly connected. 

Eb：Residual Fire Failure.

Causes : Solenoid issue. Malfunctioning PCB controller. 

Solutions : Replace the faulty PCB controller. And fix the solenoid issues. 

11. What is the normal temperature for a Tankless water heater?